1 / 36

LHC Machine Advisory Committee Meeting no. 23 , June 13 th 2008

LHC Machine Advisory Committee Meeting no. 23 , June 13 th 2008. Surface treatments and coatings for the mitigation of electron clouds in the SPS. Sergio Calatroni, Paolo Chiggiato , Pedro Costa Pinto, Mauro Taborelli Coatings, Chemistry and Surfaces TS-MME. Electron Clouds in the SPS.

mala
Télécharger la présentation

LHC Machine Advisory Committee Meeting no. 23 , June 13 th 2008

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. LHC Machine Advisory Committee Meeting no. 23, June 13th 2008 Surface treatments and coatings for the mitigation of electron clouds in the SPS Sergio Calatroni, Paolo Chiggiato, Pedro Costa Pinto, Mauro Taborelli Coatings, Chemistry and Surfaces TS-MME

  2. Electron Clouds in the SPS Effects of electron clouds (EC): • Pressure rises generated by electron induced desorption. • Increased heat load. • Emittance growth. • Beam instability: head-tail instabilities and bunch-to-bunch coupling. • Interference on the electrodes of beam pick-up monitors In 1999, for the first time, EC were identified in the SPS with an LHC-beam configuration. • EC instabilities are a limiting factor for the SPS as LHC injector. • To avoid the built-up of EC, simulations indicate that the maximum secondary electron yield of the beam pipe walls shall be less than 1.3. G. Arduini et al. LHC Project Report 423

  3. Mandate of the SPS-U Working Group • This Study Team should: • identify limitations in the existing SPS and • propose and study possible solutions … • The ultimate goal is to reliably provide the LHC with the beam required for reaching ten times the nominal luminosity. • A Design Report shall be published in 2010 describing the proposed actions and their estimated cost and planning. AB dept:  G. Arduini , F. Caspers,  K. Cornelis, E. Metral, G. Rumolo; E. Shaposhnikova; F. Zimmermann AT dept: E. Mahner;  B. Henrist. TS dept: S. Calatroni; P. Chiggiato; M. Taborelli; Ch. Vallgren Our main role: to find out a thin film (SPS compatible) with dmax < 1.3. Subsequently, to prepare a viable strategy for the coating of about 1000 SPS stainless steel vacuum chambers during the shut-down periods. Elena Shaposhnikova, http://paf-spsu.web.cern.ch/paf-spsu/

  4. Ti-Zr-V Coatings: the Case of the LHC’s LSS Low SEY are obtained for Ti-Zr-V coatings after heating in vacuum. • Most of the Long Straight Sections of the LHC are coated with Ti-Zr-V : • more than 1200 vacuum chambers were produced; • about 15 Kg of Ti-V-Zr is spread over 6 Km of LHC beam pipe; • vacuum commissioning almost concluded.

  5. Ti-Zr-V Coatings: the Case of the LHC’s LSS

  6. Heating Temperature Limitations Ti-Zr-V activation must be carried out at temperatures higher than 180°C; the nominal heating temperature for the LHC’s LSS is 230°C. • These temperatures are too high for some future CERN projects: • SPS-Upgrade: • Embedded in the magnets,the vacuum chambers cannot be heated. • CLIC positron damping ring: • heating temperatures shall be presumably limited to 150°C because of the complex installed devices, mainly SC wigglers and beam monitors. • PS-2: • Maximum heating temperature to be defined, but most likely as low as possible.

  7. Thin Films and Treatments: Possible Candidates - 1 Presented at the last MAC by T. Kroyer To abandon the seek of low SEY surfaces and opt for clearing electrodes installed along the vacuum chambers. Possible Solutions To render the surface rough enough to block secondary electrons. To find out thin films with an intrinsically low SEY. … or both combined Lower activation temperature NEG No need of heating once in vacuum By machining By chemical or electrochemical methods By coating

  8. Thin Films and Treatments: Possible Candidates - 2 • SEY high for insulators (for example MgO, CsI, Al2O3 and diamond) • SEY low for light metals (Ti) and graphite • Strongly dependent on surface cleanliness, oxidation and roughness • Strongly dependent on impinging electron dose. Many clean elements and their compounds fulfill the dmax<1.3 imposed by the SPS. Ding, Tang, and Shimizu, J. Appl. Phys. 89 (2001) 718 • But when exposed to the air their SEY increases steeply, resulting in dmax higher than about 1.5: oxides formation and water adsorption. • An additional and progressive rise is recorded during months of stay in the air, eventually leading to dmax higher than 2: airborne hydrocarbon adsorption. N. Hilleret, EPAC 2000 proceedings • Either in situ heating or particle bombardment (conditioning) is necessary to recuperate lower SEY values: surface degassing + possibly formation of a graphite layer

  9. Thin Films and Treatments: Possible Candidates - 3 The ideal film material : • has intrinsically low SEY; • is not prone to adsorb water vapor, oxygen and hydrocarbons; • can be easily deposited on stainless steel beam pipes; • is compact, smooth and not inclined to produce dust; • is UHV compatible; • has possibly low resistivity. ! Graphite could be a good compromise. SEY of graphite N. Rey Whetten, J. Appl. Phy. 34(1963)771

  10. Production and Characterization of a-C Thin Films - 1 Goal: to produce low SEY carbon films, ideally graphite thin films. However, carbon films are neither pure graphite nor pure diamond. In general they are amorphous (lack of long-range order). Locally, the carbon orbital hybridization can be diamond-like (sp3) or graphite-like (sp2). sp3 sp2 Source: Wikipedia ‘hybridization’ Our aim consists in producing amorphous carbon (a-C) films with the highest fraction of sp2 hybridization + without heating the vacuum chamber during coating (SPS constraint)

  11. -U + Production and Characterization of a-C Coatings - 2 • Typically graphite amorphous carbon films have: [S.R.P. Silva, EMIS data review] • a very low density (1.2 – 1.5 g cm-3); • very low bandgap (0 – 0.6 eV); • very low sp3 content (less than 30%); • they are compact, soft and blackish. graphite rod discharge gas Magnetron sputtering is an effective coating technique for the production of graphite amorphous carbon films. sputtered C atoms Sputtered C atoms have an energy of few eV. + beam pipe wall B Magnetron sputtering does not provide enough energy to the deposited C atoms to produce a highly packed diamond-like film: the displacement energy of C atoms in graphite is about 20 eV. Despite that, the reflected neutralized plasma ions can hit the growing film thereby influencing the sp3 C content.

  12. Production and Characterization of a-C Coatings - 3 electron gun Ip A Ic Ic Sample Is A SEY measurement XPS • Additional characterizations: • Morphology by SEM; • Thermal and electron stimulated degassing; • FTIR and Raman spectroscopy; • RBS and ERDA. • Resistivity Ip = Is + Ic d = Ic / (Is + Ic)

  13. SEY of a-C - 1 a-C film produced by magnetron sputtering on a 50 cm long, 10 cm diameter st. steel vacuum chamber (2 h exposure in the air) dmax=2.13 dmax=1.34

  14. SEY of a-C - 2 Influence of the discharge gas: a-C deposited on Cu coupon samples Kr discharge gas Ne discharge gas Measured at ICMM-CSIC in Madrid by I. Montero Herrero

  15. SEY of a-C - 3 Influence of a long exposure in the air: Kr as discharge gas dmax=1.97 2 months dmax=1.42 3 days by I. Montero Herrero

  16. SEY of a-C - 4 Influence of a long exposure in the air: Ne as discharge gas dmax=1.47 2 months dmax=1.14 3 days by I. Montero Herrero

  17. SEY of a-C - 5 Influence of the discharge gas Kr is more implanted in the graphite cathode than Ne. Implanted Kr is sputtered by Kr ions and implanted in the carbon film (sometimes it can be detected by XPS in the C film: detection limit about 0.5%). C has a higher sputtering yield when bombarded with Ne than Kr; this result in a higher deposition rate. Additional investigations are necessary to clarify the role of the discharge gas. Tests with Ar in progress…

  18. Morphology of a-C Electron Microscopy Analysis 100 nm Typical thickness ≈100 nm Substrate defects smoothed by the a-C film Very smooth surface a-C coating are used in the industry to produce very smooth surfaces SEM images by TS-MME-MM section

  19. Dust Production of the Deposited a-C Film Particle diameter larger than 0.5mm Particle diameter in the range 0.3mm and 0.5mm run# (min) run# (min) Fine dust particles are always produced during sputtering. As a matter of fact, about 10 times more particles are detected in a 2-m long vacuum chamber after coating. The particles are removed by pumping. After gentle hammering no further particles produced. In progress: coated vacuum chambers are stored under vacuum to check particle production after several weeks.

  20. a-C Carbon: Ongoing Activities • The optimization of the sputtering variables for the production of low SEY a-C coatings is in progress. • It requires the variation of the following parameter: • sputtering current and voltage ; • deposition rate and film thickness; • discharge gas pressure; • substrate treatments and temperature during the coating. • inclusion of other elements, namely N and B. The resulting SEY variations will be measured. Ripalda et al. J. Appl. Phys., Vol. 92, No. 1, 1 July 2002

  21. Smooth surface Rough surface Rough Morphologies -1 Very rough Ti, Zr, Al, Inconel ,Cu … surfaces can be obtained by chemical or electrochemical attack. However, discouraging results have been obtained for stainless steel. A rough surface can reduce secondary electron emission. (Electro)chemical attacks are hardly applicable to the existing SPS vacuum chambers.

  22. Rough Morphologies - 2 (Zr Fast Sputtering Deposition) Primary electron energy = 500eV The relative improvement is some 15%.....which means that a layer having dmax=1.35 would result in a dmax of 1.15. Once coated by a thin layer of a-C, this structure could provide SEY values well below the imposed threshold.

  23. (aC/Zr Fast Deposition) Rough Morphologies - 3 a-C onto a rough Zr coating a-C a-C/ rough Zr

  24. Rough Morphologies - 4 (Gold Black) Evaporation of metals in a relatively high pressure of a rare gas is known to produce very rough and porous films. Already mentioned in the literature, gold black has been produced and characterized. Gold black deposited by evaporation in Kr (0.5 mbar) Primary electron energy = 500eV

  25. Rough Morphologies - 5 (Gold Black)

  26. (a-C / Gold Black) Rough Morphologies - 5 No dependence on the time of exposure to the air

  27. (high pressuresputtered Cu) Rough Morphologies - 6 Measured after 2 h exposure to the air. Longer exposure ongoing…

  28. UHV Compatibility Water vapor outgassing: a-C are very smooth, therefore water desorption should not be a problem. For rough surfaces, water desorption could be a major hindrance. Outgassing measurements are planned. Electron Stimulated Desorption of a-C films e- current: 1 mA e- energy: 500 eV a-C coating Schematic view of the ESD system

  29. 15º 1mm Grooves Grooves, calculation of L.Wang at SLAC on the geometry obtained on copper at the CERN workshop Reduction also for B=0 so that we can measure SEY in the lab B=0.2T B=0 B=2T Assuming dmax=1.5 Courtesy of S.Atieh and J.M.Geisser

  30. NEG Films of Lower Activation Temperature • Some studies have already been pursued in this direction: the Ti-Zr-Nb, Zr-Fe and the Ti-Zr-Cr systems have been partially analyzed. • Interesting results have been highlighted for some Zr-Cr alloys produced by sputtering; • However, at the best, they reproduce the typical features of TiZrV. • Other alloys are expected for the next months.

  31. SPS E-cloud Experimental Tests Ecloud experiments are in progress in the SPS point 5 ECX5. Stainless steel, a-C film (Kr discharge gas) and activated Ti-Zr-V will be tested. The ecloud signal will be detected by strip detectors [G. Arduini et al., Proceeding EPAC 2002]. We do not expect remarkable results for this a-C film: its SEY should be about 1.5 Better coatings have been produced since the installation in the SPS.

  32. Implementation in the SPS - 1 • Coating pace: about 1000 chambers in 3 years during shutdowns, namely 2 arc sectors per year. • About 90 chambers per month : 4 to 5 per day. • On the coating bench, a batch of 5 chambers remains 2 days: • first day in the afternoon for installation and pumping overnight; • second day for coating, • third day in the morning for disassembling. • Two coating benches are necessary! • ECX5 cavern in the SPS underground is available.The cavern is a 20-meter diameter cylinder. Room for two coating benches and a storage area have to be fitted in it.

  33. Implementation in the SPS - 2 • We can profit of the experience acquired during the refurbishment of the cooling circuits of 255 dipole magnets, running over three years : • Repairing pace: 4 to 5 magnets per day • Buffer of 10 magnets in ECX5. • Handling. • Synchronized logistic. Courtesy of S. Sgobba TS-MME-MM

  34. Implementation in the SPS - 3 If the cleanliness of the vacuum chamber walls is unacceptable for the film adherence, cleaning have to be considered. LHC cold bore cleaning machine: it should be available for the cleaning of the SPS beam pipes. Courtesy of L. Ferreira TS-MME-CCS

  35. Implementation in the SPS - 4 • Magnets configuration in the coating bench. • The alternatives are: • Magnets laid in horizontal position: • simpler handling; • the graphite cathodes have to be supported in the vacuum chambers; • only one bench can be installed in ECX5. Magnets placed vertically (experience acquired with the LSS beam pipes): • special frame to hold the magnets (≈15 tons each); • two benches can be installed in ECX5; • easier insertion and holding of the graphite cathodes. Preliminary design in progress…

  36. Conclusions Since the beginning of the year,in the frame of the SPS-U working group, we have been seeking thin film coatings and surface treatments to mitigate electron clouds in the SPS. We intend to profit from the experience acquired during the coating of the ≈ 1200 LHC-LSS vacuum chambers. Sputter coated a-C thin films are good candidates. Their properties depend strongly on the sputtering parameters. At the present, an optimization is in progress to reduce their dmax . Bare and a-C coated rough surfaces have being considered (black coating and fast sputtering). Their compatibility with the unbaked vacuum system of the SPS has to be assessed. A preliminary design for the coating bench for the about 1000 vacuum chambers of the SPS arcs is on the starting blocks…

More Related