1 / 11

Chapter 4 Field-Effect Transistors

Chapter 4 Field-Effect Transistors. Microelectronic Circuit Design Richard C. Jaeger Travis N. Blalock. Bias Analysis Approach. Assume an operation region (generally the saturation region) Use circuit analysis to find V GS Use V GS to calculate I D , and I D to find V DS

normans
Télécharger la présentation

Chapter 4 Field-Effect Transistors

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Chapter 4Field-Effect Transistors Microelectronic Circuit Design Richard C. Jaeger Travis N. Blalock Microelectronic Circuit Design McGraw-Hill

  2. Bias Analysis Approach • Assume an operation region (generally the saturation region) • Use circuit analysis to find VGS • Use VGS to calculate ID, and ID to find VDS • Check validity of operation region assumptions • Change assumptions and analyze again if required. NOTE :An enhancement-mode device with VDS = VGS is always in saturation Microelectronic Circuit Design McGraw-Hill

  3. Four-Resistor and Two-Resistor Biasing • Provide excellent bias for transistors in discrete circuits. • Stabilize bias point with respect to device parameter and temperature variations using negative feedback. • Use single voltage source to supply both gate-bias voltage and drain current. • Generally used to bias transistors in saturation region. • Two-resistor biasing uses lesser components that four-resistor biasing and also isolates drain and gate terminals Microelectronic Circuit Design McGraw-Hill

  4. Bias Analysis: Example 1 (Constant Gate-Source Voltage Biasing) Problem: Find Q-pt (ID, VDS ,VGS) Approach: Assume operation region, find Q-point, check to see if result is consistent with operation region Assumption: Transistor is saturated, IG=IB=0 Analysis: Simplify circuit with Thevenin transformation to find VEQ and REQ for gate-bias voltage.Find VGS and then use this to find ID. With ID, we can then calculate VDS. Microelectronic Circuit Design McGraw-Hill

  5. Bias Analysis: Example 1 (Constant Gate-Source Voltage Biasing)(contd.) Check:VDS>VGS-VTN. Hence saturation region assumption is correct. Q-pt: (50.0 mA, 5.00 V) with VGS= 3.00 V Discussion: The Q-point of this circuit is quite sensitive to changes in transistor characteristics, so it is not widely used. Since IG=0, Microelectronic Circuit Design McGraw-Hill

  6. Bias Analysis: Example 2 (Load Line Analysis) Problem: Find Q-pt (ID, VDS ,VGS) Approach: Find an equation for the load line. Use this to find Q-pt at intersection of load line with device characteristic. Assumption: Transistor is saturated, IG=IB=0 Analysis: For circuit values above, load line becomes Use this to find two points on the load line. Microelectronic Circuit Design McGraw-Hill

  7. Bias Analysis: Example 2 (Load Line Analysis)(contd.) @VDS=0, ID=100uA @ID=0, VDS=10V Plotting on device characteristic yields Q-pt at intersection with VGS = 3V device curve. Check: The load line approach agrees with previous calculation.Q-pt: (50.0 mA, 5.00 V) with VGS= 3.00 V Discussion: Q-pt is clearly in the saturation region. Graphical load line is good visual aid to see device operating region. Microelectronic Circuit Design McGraw-Hill

  8. Bias Analysis: Example 3 (Constant Gate-Source Voltage Biasing with Channel-Length Modulation) Assumption: Transistor is saturated, IG=IB=0 Analysis: Simplify circuit with Thevenin transformation to find VEQ and REQ for gate-bias voltage.Find VGS and then use this to find ID. With ID, we can then calculate VDS. Problem: Find Q-pt (ID, VDS ,VGS) of previous example, given =0.02 V-1. Approach: Assume operation region, find Q-point, check to see if result is consistent with operation region Microelectronic Circuit Design McGraw-Hill

  9. Bias Analysis: Example 3 (Constant Gate-Source Voltage Biasing with Channel-Length Modulation) Check:VDS>VGS-VTN. Hence saturation region assumption is correct. Q-pt: (54.5 mA, 4.55 V) with VGS= 3.00 V Discussion: The bias levels have changed by about 10%. Typically, component values will vary more than this, so there is little value in including  effects in most circuits. Microelectronic Circuit Design McGraw-Hill

  10. Bias Analysis: Example 4 (Four-Resistor Biasing) Assumption: Transistor is saturated, IG=IB=0 Analysis: First, simplify circuit, split VDD into two equal-valued sources and apply Thevenin transformation to find VEQ and REQ for gate-bias voltage Problem: Find Q-pt (ID, VDS) Approach: Assume operation region, find Q-point, check to see if result is consistent with operation region Microelectronic Circuit Design McGraw-Hill

  11. Bias Analysis: Example 4 (Four-Resistor Biasing) Since VGS<VTNfor VGS= -2.71 V and MOSFET will be cut-off, and ID= 34.4 mA Also, Since IG=0, VDS>VGS-VTN. Hence saturation region assumption is correct. Q-pt: (34.4 mA, 6.08 V) with VGS= 2.66 V Microelectronic Circuit Design McGraw-Hill

More Related