1 / 77

Chapter 13

Chapter 13. Memory Devices and Systems. Memory Basics. Memory is used to store data or instructions for a m icro p rocessor u nit (MPU) system. The stored data is organized in an array of bits. Bits are stored in locations called addresses. Memory Types.

nowles
Télécharger la présentation

Chapter 13

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Chapter 13 Memory Devices and Systems

  2. Memory Basics • Memory is used to store data or instructions for a microprocessor unit (MPU) system. • The stored data is organized in an array of bits. • Bits are stored in locations called addresses.

  3. Memory Types • RAM (random access or Read/Write memory): Memory that can be written to or read from in a random order (addresses). • ROM (read only memory): Memory that can only be read from in a random order. • Sequential Memory: Memory that can be written to or read from but only in a sequential order (addresses).

  4. Memory Register – 1 • Simplest memory element is a D-type flip-flop or latch. • An octal latch can be used to store a byte of data.

  5. Memory Register – 2 • When WRITEn (EN) goes low, then high, the data on DATA_IN [7..0] is latched into the register. • When READ is set to a 1, the latch data output is enabled to DATA_OUT. • When READ = 0, the DATA_OUT lines are tristated.

  6. Memory Register – 2

  7. Memory Register – 2

  8. Memory 4 x 8 (Write) – 1 • Uses four octal latches to store 4 bytes of data at different addresses (see Figure 13.5 in textbook). • Instantiated as megafunctions based on the LPM_LATCH. • 8-bit tristate output instance of the LPM_BUSTRI component.

  9. Memory 4 x 8 (Write) – 2 • A 2-to-4 decoder is used to select the Latch (1 of 4) based on the address input on ADDR[0..1]. • The input data (to be written) is placed on dat_in[0:7] and the address of the byte on ADDR[0..1].

  10. Memory 4 x 8 (Write) – 3 • The WRITE signal is pulsed low to select 1 of the 4 bytes and write the data to that register. • None of the other registers has data written into them.

  11. Memory 4 x 8 (Read) – 1 • Data from each latch is output to the inputs of an octal (8-bit) 4-to-1 multiplexer. • The address inputs are applied to the MUX select lines (ADDR[0..1]) to select 1 of the 4 data input bytes and transfer it to the MUX output.

  12. Memory 4 x 8 (Read) – 2 • The data is then read by READ = 1 to enable the tristate drivers and place the byte on dataout. • Again the data from one and only one address is read at a time. • If two or more were read simultaneously, there would be bus contention.

  13. Memory 4 x 8 (Read) – 2

  14. Memory Capacity • Memory size is specified by the address and data size such as 4 (addresses) x 8 (data). • A 4 x 8 memory block stores 32 bits or 4 bytes with 1 byte = 8 bits. • Large memory devices use the designators K (kilobits = 1024 bits), M (mega = 1048576 bits), or G (giga = 1073741824).

  15. Address Lines – 1 • A memory device of 8K x 8 (8 kilobits) would require 13 address lines to address all locations in the device (213 = 8192 = 8 x 1024). • The address of the first byte (13 bits of data) is = 0 0000 0000 0000, the second byte is at = 0 0000 0000 0001, and so on with the last byte at address 8191 = 1 1111 1111 1111.

  16. Address Lines – 2 • A memory device covers a range of addresses such as 0000H to 1FFFH (given in HEX) for the 8K device. • All memory devices require address lines to point to a location in the memory array.

  17. Address Lines – 3

  18. Address Lines – 4

  19. Memory Control Lines – 1 • Memory devices require data lines (depends on organization of arrays (bit, nibble, byte)) and address lines (depends on size of array). • Memory devices also require some control lines to define the read or write processes.

  20. Memory Control Lines – 2 • All memory devices have one (or more) enable inputs such as chip enable (CE) or chip select (CS). • The CS/CE line is used to enable the memory to allow read or write data transfers. (Usually Active Low ). • When it is a 1, the device cannot be accessed.

  21. Memory Control Lines – 3 • RAM memory devices have a write (W or WE) signal to allow data to be written TO memory (if CS is active). • All memory devices have a read (G or OE) signal to allow data to be read FROM memory (if CS is active). • Some SRAM devices have a R/W signal, does both.

  22. Memory Control Lines – 3

  23. RAM Definitions – 1 • Volatile: A memory is volatile if its stored data is lost when electrical power is lost. • Static Ram (SRAM): Consists of arrays of memory cells that are flip-flops. Data is stored in a cell indefinitely until power is turned off.

  24. RAM Definitions – 2 • Dynamic RAM (DRAM): Consists of arrays of memory cells that are capacitors. The data is stored as a charged or discharged state on the capacitor. • The capacitor can only hold the charge for a short time (ms), and then it needs to be refreshed.

  25. SRAM/DRAM Comparison • DRAMs have larger memory capacity. A single DRAM = 256 MB, a DRAM Module = 1 GB (for gigabyte). • DRAMs consume less board area. • DRAMs require refreshing and multiplexed addresses. • SRAMs have faster access times.

  26. SRAM Memory Cell – 1 • Three basic SRAM cell technologies are bipolar, NMOS, and CMOS. • All three types use cross-coupled transistors to make up the basic flip-flop storage cell.

  27. SRAM Memory Cell – 2

  28. SRAM Memory Cell – 3

  29. SRAM Memory Cell – 4

  30. SRAM Memory Cell – 5 • In the basic NMOS cell, Q1 and Q2 are always biased to act as a Load Resistor for Q3 and Q4. • The Data in a cell can be read by setting ROW_SELECT = 1 to turn on Pass Transistors Q5, Q6. • The Data from cell is then “passed” to the BIT Line and Line.

  31. SRAM Memory Cell – 6 • To store a ‘0’, place a 0 on the bit line and set ROW_SELECT = 1. • This turns on the Pass Transistors (Q5, Q6) to place a 0 to Q4 (it is off). • Q3 is then ON to store the 0. • A ‘1’ can be stored in a similar fashion.

  32. SRAM Array Design – 1 • The cells are placed in a 512 row by 8192 column array. • The address buffer splits the address inputs (A0–A18) for the column and row decoders.

  33. SRAM Array Design – 2

  34. SRAM Array Design – 3 • Columns are divided into groups of 8 bits (for a 1-byte output) for each read or write operation. • The data in or out is provided on the 8-bit data bus on the array.

  35. DRAM Cells – 1 • Basic cell is a MOS capacitor (to store charge) and a pass transistor. • Capacitor charge will “leak” and needs to be refreshed every 8 to 64 ms (depends on the size of the array). • Adds more complexity to read/write cycles to allow refreshing.

  36. DRAM Cells – 2

  37. DRAM Cells – 3 • Memory cells have fewer components than a SRAM device. • This accounts for the higher densities possible than with SRAM.

  38. DRAM Arrays – 1 • Most DRAM devices are bit organized (a single bidirectional data pin) instead of word (usually a group of 8 data pins) in SRAM. • DRAMs use a multiplexed row and column address inputs to the array to save on pin count on the IC.

  39. DRAM Arrays – 2 • The multiplexed row and column address inputs must be demultiplexed to send to separate row and column decoders for the array. • Two negative edge trigger controls are used to latch addresses to the R/C buffers.

  40. CAS/RAS

  41. CAS/RAS

  42. CAS/RAS Timing • Refer to Figure 13.15 in the textbook. • First the row address (usually lower order address lines) are input and loaded by the low pulse on RAS. • Then the column addresses are input and loaded by a low pulse on CAS.

  43. ROM Basics • ROM is nonvolatile memory and it is used to store firmware such as a PC operating system (the BIOS). • Stores data that executes tasks that do not change such as a “Bootstrap” program for an MPU.

  44. ROM Array – 1 • First type of ROM is called a MASK ROM, because the data is stored permanently during the ROM manufacturing (or fabrication). • A logic 0 is stored by connecting the drain of the MOSFET to the column line. • MASK ROM now replaced by FLASH memory.

  45. ROM Array – 2

  46. ROM Array – 3 • A logic 1 is stored as an open connection, it just floats to a 1. • The Row and Column Select Lines are used to read data through the Sense Amplifier.

  47. EPROM Basics • Erasable Programmable ROM: A ROM that can be programmed (“burned”) by the user and erased later by exposing it to UV light. • It is nonvolatile and reprogrammable. • The basic structure of the EPROM cell is based on the FAMOS FET.

  48. EPROM Programming – 1 • The FAMOS FET is a floating gate avalanche MOSFET Gate. • An unprogrammed FAMOS cell has a low threshold, so the transistor is turned ON to store a logic 1. • The cell is programmed by a high energy (12 V to 25 V) pulse on the row select to raise threshold for a logic 0.

  49. EPROM Programming – 2 • The actual programming involves writing a logic 0 to cells and leaving the others unprogrammed (logic 1). • Erasing is done by exposure to UV light for 20 to 45 minutes. • This sets all cells to the unprogrammed state (logic 1) by releasing electrons trapped in the floating gate.

  50. Applications • EPROMs can be used for logic tables and LUT for logic designs. • Figure 13.18 in the textbook shows how to use an EPROM with a Digital-to- Analog Converter (DAC) to store waveform data such as sine, ramp, or triangle.

More Related