1 / 27

POWER ELECTRONICS

بسم الله الرحمن الرحيم. The Islamic University of Gaza Faculty of Engineering Electrical Engineering Department. POWER ELECTRONICS . EELE 5450 — Summer 2012. Instructor: Eng. Jalal Al Roumy. Lecture 24. Power switches. Power Semiconductor Devices .

qiana
Télécharger la présentation

POWER ELECTRONICS

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. بسم الله الرحمن الرحيم The Islamic University of Gaza Faculty of Engineering Electrical Engineering Department POWER ELECTRONICS EELE 5450— Summer 2012 Instructor: Eng. Jalal Al Roumy Lecture 24

  2. Power switches

  3. Power Semiconductor Devices Power devices are the key elements of a power converter. The commonly used devices are: (1) Power Diode (2) Silicon-Controlled Rectifier (SCR) or Thyristor (3) Gate Turn-off Thyristor (GTO) (4) Power Bipolar Junction Transistor (Power BJT) (5) Power Metal-Oxide Field-Effect Transistor (Power MOSFET) (6) Insulated-Gate Bipolar Transistor (IGBT) (7) Gate controlled thyristors (IGCT).

  4. C (collector) IC B (base) + VCE _ IB E (emitter) Bipolar Junction Transistor (BJT) • Ratings: Voltage: VCE<1000, Current: IC<400A. Switching frequency up to 5kHz. Low on-state voltage: VCE(sat) : 2-3V • Low current gain (b<10). Need high base current to obtain reasonable IC . • Expensive and complex base drive circuit. Hence not popular in new products.

  5. D (drain) ID G (gate) + VDS _ + VGS _ S (source) Mosfet • Ratings: Voltage VDS<500V, current IDS<300A. Frequency f >100KHz. For some low power devices (few hundred watts) may go up to MHz range. • Turning on and off is very simple. • To turn on: VGS =+15V • To turn off: VGS =0 V and 0V to turn off. • Gate drive circuit is simple

  6. C (collector) IC + VCE _ G (gate) + VGE _ E (emitter) IGBT: symbol Insulated Gate Bipolar Transistor (IGBT) • Combination of BJT and MOSFET characteristics. • Gate behaviour similar to MOSFET - easy to turn on and off. • Low losses like BJT due to low on-state Collector-Emitter voltage (2-3V). • Ratings: Voltage: VCE<3.3kV, Current,: IC<1.2kA currently available. Latest: HVIGBT 4.5kV/1.2kA. • Switching frequency up to 100KHz. Typical applications: 20-50KHz.

  7. A (Anode) Ia + Vak _ Ig K (Cathode) GTO: Symbol Gate turn-off thyristor (GTO) • Behave like normal thyristor, but can be turned off using gate signal • However turning off is difficult. Need very large reverse gate current (normally 1/5 of anode current). • Gate drive design is very difficult due to very large reverse gate current at turn off. • Ratings: Highest power ratings switch: Voltage:Vak<5kV; Current: Ia<5kA. Frequency<5KHz. • Very stiff competition: • Low end-from IGBT. High end from IGCT

  8. Ia + Vak _ IGCT Ig K (Cathode) Insulated Gate-Commutated Thyristor (IGCT) • Among the latest Power Switches. • Conducts like normal thyristor (latching), but can be turned off using gate signal, similar to IGBT turn off; 20V is sufficent. • Power switch is integrated with the gate-drive unit. • Ratings: • Voltage: Vak<6.5kV; Current: Ia<4kA. Frequency<1KHz. Currently 10kV device is being developed. • Very low on state voltage: 2.7V for 4kA device

  9. 1GW Thyristor 10MW GTO/IGCT 10MW 1MW IGBT 100kW 10kW MOSFET 1kW 100W 10MHz 100kHz 1MHz 10Hz 1kHz Power Switches: Power Ratings

  10. Switches comparisons (2003)

  11. Drivers and Snubbers

  12. Driver circuit (Base / gate) • Interface between control (low power electronics) and (high power) switch. • Functions: – amplifies control signal to a level required to drive power switch – provides electrical isolation between power switch and logic level • Complexity of driver varies markedly among switches. MOSFET/IGBT drivers are simple but GTO drivers are very complicated and expensive.

  13. ELECTRICAL ISOLATION FOR DRIVERS • Isolation is required to prevent damages on the high power switch to propagate back to low power electronics. • Normally opto-coupler (shown below) or high frequency magnetic materials (as shown in the thyristor case) are used. • Many standard driver chips have built-in isolation. For example TLP 250 from Toshiba, HP 3150 from Hewlett-Packard uses opto-coupling isolation.

  14. ELECTRICAL ISOLATION FOR DRIVERS • Power semiconductor devices can be categorized into 3 types based on their control input requirements: • Current-driven devices – BJTs, MDs, GTOs • Voltage-driven devices – MOSFETs, IGBTs, MCTs • Pulse-driven devices – SCRs, TRIACs

  15. CURRENT DRIVEN DEVICES (BJT) • Power BJT devices have low current gain due to constructional consideration, leading current than would normally be expected for a given load or collector current. • The main problem with this circuit is the slow turn-off time.

  16. ELECTRICALLY ISOLATED DRIVE CIRCUITS

  17. EXAMPLE : GATE DRIVE FOR THYRISTORS • Pulse transformer is used for isolation. R1is to limit the gate current • Normally a pulse with length 10us with amplitude of 50mA is sufficient to turn-on the thyristors. It is quite common to fire the thyristors with successive pulses to ensure proper turn-on. • It is not possible to turn-offa thyristor with the above circuit

  18. SIMPLE MOSFET GATE DRIVER • Note: MOSFET requires VGS =+15V for turn on and 0V to turn off. LM311 is a simple amp with open collector output Q1. • When B1 is high, Q1 conducts. VGS is pulled to ground. MOSFET is off. • When B1 is low, Q1 will be off. VGS is pulled to VGG. If VGG is set to +15V, the MOSFET turns on.

  19. RCD SNUBBERS • In general, snubbers are used for: • Turn-on:to minimize large over-currents through the device during turn-on. • Turn-off:to minimize large over-voltages across the device during turn- off. • Stress reduction: to shape the device switching waveform such that the voltage and current associated with the device are not high simultaneously.

  20. Heatsink

  21. Heat Removal Mechanism Fin-type Heat Sink SCR (hokey-puck-type) on power pack kits SCR (stud-type) on air-cooled kits Assembly of power converters

  22. Applications

  23. Static Application: DC Power Supply AC voltage DC-DC DIODE FILTER LOAD CONVERTER RECTIFIER AC LINE VOLTAGE V control F F (1 or 3 ) (derived from feedback circuit) Static Application: DC Power Supply

  24. Drive Application: Air-Conditioning System

  25. Uninterruptible Power Supply (UPS)

  26. Powering Automotive System

  27. Motor Drive System End of Lecture

More Related