1 / 30

PERSPECTIVES & ELEVATIONS

PERSPECTIVES & ELEVATIONS. To draw a room to “perspective”, means to make a 3D drawing that looks realistic… the way it would appear if you were actually standing and looking at the room. It is called a “ rendering ”.

rasha
Télécharger la présentation

PERSPECTIVES & ELEVATIONS

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. PERSPECTIVES & ELEVATIONS

  2. To draw a room to “perspective”, means to make a 3D drawing that looks realistic… the way it would appear if you were actually standing and looking at the room. It is called a “rendering”. To begin, you need a floor plan of the room, drawn to scale. Measure the room, look at the way the furnishings are laid out, and decide where you will stand to view this room the best. In this room, it would be best to stand on the wall with the door. Doing that, this room is wider than it is deep…14’ wide and 11’ deep. Follow directions for a room that is wider than it is deep. Select your floor plan... We’ll stand on this wall

  3. Step 1: Starting to draw... Using plain paper, not graph paper. Select paper to draw on. If the ceilings of your room are 8’ tall, you will need a piece of paper at least 8” in one direction. The other dimension of your paper must accommodate the width of the room. We are drawing a room that is 14’ wide. Therefore, the paper we need must be 8” x 14”. The depth of the room will not be a factor in choosing our paper, in a room that is wider than deep. Scale: 1’ on floor plan = 1” on perspective Step 1: Place your paper in a horizontal position. Using your ruler and pencil, draw a line near the bottom of your paper that is 14” long… to represent one of the 14’ wide floor lines of your room. Be precise with your measurements! You may want to stand over the top of the ruler and look directly down on it. Mark the line in inches, starting with zero as shown. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  4. Step 2: The wall line... Step 2: Now that you have the 14’ floor line in place, it is time to add the left wall line. Using a 90 degree square angle, draw a vertical line up from the floor line. Begin at zero, and number each foot. Our room has 8’ high ceilings, so our wall is 8’ tall, and therefore our wall line is 8” long. 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  5. Step 3: Finishing the rectangle... Step 3: Finish drawing the rectangle by using your square to put in the right wall and ceiling. Use extra care in making sure all of your measurements are accurate. Even a hairline error now can result in a measurable error later on as we continue the perspective. If you have time, you might want to mark the right wall line in inches… it would look like the left wall line, marked off from 0 – 8’. 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  6. Step 4: Adding the horizon line... Step 4: In art class, the next line we’re going to add is called the horizon line. In drawing a room perspective, this line represents “eye level”. You have to make a decision now… do you want to view this room as if your eyes were at a 5’ level? The lower you place the horizon line below 5’, the more you will be looking UP at the room’s furnishings. The higher you place the horizon room above 5’, the more you will be looking DOWN on the room’s furnishings. For this practice perspective, place the horizon line at 5’. The room you draw will appear the way you see it if your eyes are 5’ above the floor. Use a square and measure carefully to draw this line. If you marked the 8’ on the right wall, you will simply connect the two 5’ markings. 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  7. Step 5: Adding the vanishing point... Step 5: To complete this step, you have to make another decision. Do you want to view the room as if you were standing clear over by the left wall? ( you won’t see the mirror over the dresser very well, but you will see the window treatment)...or clear over by the right wall? (you won’t see the window treatment very well, but will see the dresser mirror) ...or standing right in the middle of the room? (you will see both side walls equally well). For this example, let’s position ourselves exactly in the middle. X X If there are furnishings on the wall you are standing, they will not be shown on your perspective drawing.

  8. Step 5: Adding the vanishing point... Now that you’ve determined where you are going to stand in the room, locate that X on the floor line of your perspective drawing. (we were standing 7 foot from the left wall) Now, using your square once again, locate the spot on the horizon line that is directly above that X on the floor line. This new spot is your vanishing point. Mark it with a simple line. 8 7 6 5 4 3 2 1 0 X 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  9. Step 6: Connecting the corners... Step 6: Connect all four corners to the vanishing point. Use a dotted line for this step, as part of each line will be temporary. The top dotted lines will represent the ceiling lines of your room when it is drawn to perspective; the bottom dotted lines will represent the floor lines. 8 7 6 5 4 3 2 1 0 X 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  10. Step 7: Adding the room depth... Step 7: Connect a diagonal line from “eye level on the left wall” TO “the number on the floor line that represents the depth of the room”. Our practice room is 11’ deep, so we draw from 5’ up on the left wall diagonally down to the 11’ mark on the floor line. Use a solid line. 8 7 6 5 4 3 2 1 0 X 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  11. Step 8: Finishing the back wall... Step 8: Where the solid diagonal line crosses the left floor line, draw in the four corners of the back wall. Start where the flashing circle indicates. Accuracy is really important here! If your measurements have been slightly off before… it will show up now. Make small adjustments as necessary during this step, trying to get a perfect rectangle. 8 7 6 5 4 3 2 1 0 X 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  12. Step 9: Starting the floor grid... Step 9: If you’re getting confused, now is the time to clean up your drawing. Erase the parts of the dotted lines that fall within the back wall rectangle. You can erase the eye level line that crosses the back wall also…but only on the back wall, not entirely. If you put an X on the bottom floor line, remove it now. BE CAREFUL NOT TO DISTURB THE VANISHING POINT. You will continue to need this marking. To start the floor grid, connect each number on the floor with the vanishing point. Draw up TO the back wall rectangle, but not all the way to the vanishing point itself. 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  13. Step 10: Finishing the floor grid... Step 10: Where the diagonal line (the one shown in green here) crosses each of the floor grid lines, use your square to draw a perfectly horizontal line. Those horizontal lines need to be perpendicular to the left or right wall lines. Use your eyes! Make sure those lines look straight, are spaced and are drawn evenly. The little squares that are formed on the floor grid should duplicate the squares on your floor plan. The floor grid on this perspective drawing should have 14 squares across and 11 squares going back… duplicating the 11’ x 14’ foot room plan. 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  14. Step 11: Adding the furnishings... Step 11A: Let’s start with the bed. Look at the floor plan. Use dots to plot the 4 corners of the bed on the floor grid. Those dots are shown here, enlarged and in red. 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  15. Step 11B: The next step is to put in lines on one or both of the side walls that represent the height of the bed. A bed is approximately 24 inches high, so we’ll put in a height line on the left wall. Draw the height line, starting at the 2’ mark and drawn to the vanishing point. You can stop drawing at the back wall. It is shown here in a dotted green line. 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  16. Step 11C: Follow each dot for a bed corner along the floor grid line TO the left wall, then follow it UP to the 2’ line, and then back across the room perpendicular to the left wall line. It is shown here by a red, dotted line. The only line done so far is from the red dots on the grid line that are closest…not the ones on the back wall line. • Dots to the wall • Follow the floor grid to the wall, and up to the height line • Square off through the height line 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  17. Think of the bed as a rectangular form… can you visualize the end of the bed now, using the floor grid, vertical uprights, and red dotted top line? Step 11D: You can now draw the two nearest corners of the bed form. Use your square, and draw the lines perfectly vertical, from each dot UP to the height line. • Dots to the wall • Follow the floor grid to the wall, and up to the height line • Square off through the height line • Draw the corners vertically up to the new line 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  18. On our rectangular bed form, we’re adding the back wall of the form. Step 11 E: Now we’ll put in the back side of the bed form. Follow the same steps… “dots to the wall, wall to the height line, square off through the height line, and then draw the corners up. 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  19. Step 11 F: Now that you have all four corners of the bed form drawn to the right height, the final step in drawing the bed is to connect the corners. Think carefully about which lines will “show”, and which ones will not. Connect the corners; draw all visible lines and erase all unnecessary lines and dots 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  20. Step 11G: Add the dresser with mirror. The dresser itself is 30 inches tall. The mirror is 3’ wide x 4’ tall; center it on the 5’ wide dresser by marking it on the floor grids and drawing straight up to a 6 1/2’ height line. 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  21. Step 11H: Add the nightstand. It is 24 inches tall, like the bed. Because of the angle you are viewing it at, it may appear to be attached to the bed, even though it has a 6” clearance. 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  22. Step 11 I: Add the window. On the floor plan you can see that it is 5’ wide, but now you have to decide how tall the window actually is. We will draw it 5’ tall… starting 2’ off the floor and ending at the 7’ height line. For this, you may have to mark the feet on the right hand wall if you have not already done so. To mark the vertical sides of the window, you will work from the floor grids. 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  23. Step 11J: At this point, you may want to add some additional details to improve the appearance of your room. Use your eyes… perhaps adding a frame around the mirror and window, or a headboard on the bed, drawers on the dresser, blinds or window treatment, or a plant. 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

  24. Step 11K: Now it’s time to make the final tracing. Trace just the lines you want to keep. Trace the entire floor grid for a tiled floor, or just the lines in one direction for a wood floor as shown here, or none of the grid for carpeting. Add a title, and your name. 11’ x 14’ GUEST BEDROOM by Your Name

  25. Step 12: Add color by “shading” your picture. Shading is not the same as coloring. When shading, you must first establish a light source, and then put color only where there would be shadows. If the light source is from the upper right hand corner, then the left side of furniture pieces would be shaded. Shading must be done directionally… following major lines. When shading, there will be some areas of the room that remain white and uncolored. Shading is simply a ‘suggestion’ of color. This completed picture is called a ‘rendering’. 11’ x 14’ GUEST BEDROOM by Your Name

  26. Elevations... Use the same steps you used for drawing a room perspective to draw a single item or wall arrangement. This is called an “elevation”, and allows you to show detail better.

  27. Elevations... Elevation drawings can be used to show the exterior and landscaping of your home.

  28. PERSPECTIVES & ELEVATIONS The End

  29. 11’ x 14’ GUEST BEDROOM by Your Name

  30. Drawing your own room, in perspective... Name: ______________________ Due Date: ___________________ You have already been assigned a ranch-style house floor plan. As soon as that is finished, you are ready to begin this assignment. • Select one room (or area of one room) from your ranch-style house floor plan, and use that room for a perspective drawing. Choose carefully, thinking about the dimensions of the room (we’ve only practiced rooms that are wider than they are deep), and where you will stand in the room. • A bedroom with just a bed, nightstand(s), and dresser is the easiest room to draw. That choice is certainly acceptable, but if you’re looking for a challenge, try the living room. The greatest challenge is the kitchen. The degree of difficulty will be taken into consideration at grading time. • Draw this room to perspective. • Shade the room, to finish the rendering.

More Related