1 / 19

Nonlinear Force Free Field Extrapolations for AR 10486 Pre and Post Flare

Nonlinear Force Free Field Extrapolations for AR 10486 Pre and Post Flare. J.McTiernan 19-Jul-2006. Some Jargon:. Force-free field: JxB = 0, current J is parallel to B Alpha: constant of proportionality, J = α B Linear Force-free field: α is a spatial constant

sarila
Télécharger la présentation

Nonlinear Force Free Field Extrapolations for AR 10486 Pre and Post Flare

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Nonlinear Force Free Field Extrapolations for AR 10486Pre and Post Flare J.McTiernan 19-Jul-2006

  2. Some Jargon: • Force-free field: JxB = 0, current J is parallel to B • Alpha: constant of proportionality, J = αB • Linear Force-free field: αis a spatial constant • Non-linear Force-free field: αis not constant • Potential field: α= 0, J = 0, also called “current-free”

  3. Optimization method: Wheatland, Roumeliotis & Sturrock, Apj, 540, 1150 Objective: minimize the “Objective Function” We can write: If we vary B, such that dB/dt = F, and dB/dt = 0 on the boundary, then L will decrease.

  4. Optimization method: Wheatland, Roumeliotis & Sturrock, Apj, 540, 1150 Objective: minimize the “Objective Function” We can write: If we vary B, such that dB/dt = F, and dB/dt = 0 on the boundary, then L will decrease.

  5. Optimization method (cont): • Start with a box. The bottom boundary is the magnetogram, the upper and side boundaries are the initial field. Typically start with potential field or linear FFF, extrapolated from magnetogram. • Calculate F, set new B = B + F*dt (typical dt =1.0e-5). B is fixed on all boundaries. • “Objective function”, L, is guaranteed to decrease, but the change in L (ΔL) becomes smaller as iterations continue. • Iterate until ΔL approaches 0. • The final extrapolation is dependent on all boundary conditions and therefore on the initial conditions. • Requires a vector magnetogram, with 180 degree ambiguity resolved. • See Schrijver, et al. 2006, Solar Physics 235, 161 for comparison of methods, and limitations of NLFFF’s.

  6. The starting point is a potential field, extrapolated from Bz on the surface: Note that the potential field lines do not show shear in the field. Colors? The brighter lines have stronger Bz at the surface.

  7. Here is the NLFFF: These are the same field line starting points shown earlier. There are some differences.

  8. Bx By Bz Start with a VECTOR magnetogram With 180° amiguity resolved: MFSC data : D.Falconer 29-Oct-2003 18:31:00 UT And 29-Oct-2003 21:27:00 UT Pre-flare Post-flare Note “patchiness” in Bx, By; this is not so good.

  9. Pre flare field lines: Post flare field lines This is a blow-up of the flare region. The ‘start points’ of the field lines (on the left side) are the same in both images. (co-alignment is good to 5 arcsec). The post-flare lines look more like potential field lines.

  10. What about the pre and post flare magnetic energy? • Pre-flare energy = 2.466e33 ergs • Post-flare energy = 2.430e33 ergs • ΔE = -3.66e31 ergs. Is this significant? • Uncertainties from Monte Carlo calculation: • Assumed uncertainties: 25 G in Bz, 50 G in Bx, By • σΔE = 2.28e32 ergs • The energy change is negligible compared to the uncertainty.

  11. What about the flare footpoints? Pre flare VM is 2 hrs before the X flare. Post flare VM is < 1hr after peak. So the loops seen here may or may not correspond to our B field. TRACE image with RHESSI contours

  12. The footpoints move outwards in both directions: Can we find field lines that look as if they connect the footpoints? IVM Bz, with RHESSI 50 – 100 keV footpoints, at different times: A: 20:43:40 to 20:44:40UT B: 20:51:12 to 20:52:12UT C: 20:58:40 to 20:59:40UT

  13. Pre flare field lines: Post flare field lines Post-flare lines are much better than pre-flare lines when connecting footpoints.

  14. For the pre-flare field, lines from right-hand footpoints A and B end 20 arcsec below corresponding left-hand footpoints.

  15. For the post-flare field, lines from right-hand footpoints A and B end within 5-10 arcsec of the corresponding left-hand footpoints.

  16. The ‘post-flare loops’ are high 50 to 100 Mm. The pre-flare sheared field lines were lower, Less than 30 Mm. Post-flare Pre-flare

  17. Conclusions? Post-flare field looks more ‘potential’, but the difference in energy between the two magnetograms is not significant. “Post-flare loops” in the post-flare magnetogram are aligned in the same direction as the HXR footpoints, this was hard to see in the pre-flare magnetogram. Future work? Better alignment. Also try different ambiguity resolution. The NLFFF code is part of SSW, try: IDL>ssw_upgrade, /nlfff, /spawn See http://sprg.ssl.berkeley.edu/~jimm/fff/optimization_fff.html for documentation.

More Related