1 / 33

Announcements

Announcements. Homework #1 statistics (for on-campus students): Average = 65.2/80 = 82% Homework #3 due Friday, Feb. 8 for on-campus students Correction to Problem 19.6:

Albert_Lan
Télécharger la présentation

Announcements

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Announcements • Homework #1 statistics (for on-campus students): • Average = 65.2/80 = 82% • Homework #3 due Friday, Feb. 8 for on-campus students • Correction to Problem 19.6: Part (a) asks you to derive expression for Voc and Isc in terms of the variables F = fs/ finf, Vg, n = Cs / Cp, and Rinf. There is a square root missing from Rinf, i.e. it should read

  2. A series resonant link inverter Same as dc-dc series resonant converter, except output rectifiers are replaced with four-quadrant switches:

  3. 19.4.4 Design Example • Select resonant tank elements to design a resonant inverter that meets the following requirements: • Switching frequency fs = 100 kHz • Input voltage Vg = 160 V • Inverter is capable of producing a peak open circuit output voltage of 400 V • Inverter can produce a nominal output of 150 Vrms at 25 W

  4. Solve for the ellipse which meets requirements

  5. Calculations The required short-circuit current can be found by solving the elliptical output characteristic for Isc: hence Use the requirements to evaluate the above:

  6. Solve for the open circuit transfer function • The requirements imply that the inverter tank circuit have an open-circuit transfer function of: • Note that Voc need not have been given as a requirement, we can solve the elliptical relationship, and therefore find Voc given any two required operating points of ellipse. E.g. Isc could have been a requirement instead of Voc

  7. Solve for matched load (magnitude of output impedance ) • Matched load therefore occurs at the operating point Hence the tank should be designed such that its output impedance is

  8. Solving for the tank elementsto give required ||Zo0|| and ||Hinf|| • Let’s design an LCC tank network for this example The impedances of the series and shunt branches can be represented by the reactances

  9. Analysis in terms of Xs and Xp • The transfer function is given by the voltage divider equation: The output impedance is given by the parallel combination: Solve for Xs and Xp:

  10. Analysis in terms of Xs and Xp

  11. ||Hinf||

  12. ||Zo0||

  13. ||Zo0||

  14. Analysis in terms of Xs and Xp

  15. Analysis in terms of Xs and Xp • The transfer function is given by the voltage divider equation: The output impedance is given by the parallel combination: Solve for Xs and Xp:

  16. Evaluate tank element values

  17. DiscussionChoice of series branch elements • The series branch is comprised of two elements L and Cs, but there is only one design parameter: Xs = 733 Ω. Hence, there is an additional degree of freedom, and one of the elements can be arbitrarily chosen. • This occurs because the requirements are specified at only one operating frequency. Any choice of L and Cs, that satisfies Xs = 733 Ω will meet the requirements, but the behavior at switching frequencies other than 100 kHz will differ. • Given a choice for Cs, L must be chosen according to: For example, Cs = 3Cp = 3.2 nF leads to L = 1.96 mH

  18. Rcrit • For the LCC tank network chosen, Rcrit is determined by the parameters of the output ellipse, i.e., by the specification of Vg, Voc, and Isc. Note that Zo is equal to jXp. One can find the following expression for Rcrit: Since Zo0 and H  are determined uniquely by the operating point requirements, then Rcrit is also. Other, more complex tank circuits may have more degrees of freedom that allow Rcrit to be independently chosen. Evaluation of the above equation leads to Rcrit = 1466 Ω. Hence ZVS for R < 1466 Ω, and the nominal operating point with R = 900 Ω has ZVS.

  19. Ellipse again with Rcrit, Rmatched, and RnomShowing ZVS and ZCS

  20. Converter performance • For this design, the salient tank frequencies are • (note that fs is nearly equal to fm, so the transistor current should be nearly independent of load) The open-circuit tank input impedance is So when the load is open-circuited, the transistor current is Similar calculations for a short-circuited load lead to

  21. Extending ZVS range

  22. Extending ZVS range

  23. Extending ZVS range

  24. Dynamic Modeling and Analysisof Resonant Inverters Closed-loop control system to regulate amplitude of ac output (Lamp ballast example shown, but other applications have similar needs) (frequency modulation control shown) • Issues for design of closed-loop resonant converter system: • Need open-loop control-to-output transfer function to model loop gain, closed-loop transfer functions • How does control-to-output transfer function depend on the tank transfer function H(s)?

  25. Sinusoidal steady-state resonant inverter behavior

  26. Dynamic analysis of resonant inverters

  27. DC gain of control-to-output envelope transfer function

  28. Spectrum of v(t) The control input is varied at modulation frequency fm This leads to sidebands at frequencies fs ± fm (true for both AM and narrowband FM) The spectrum of v(t) contains no component at f = fm. • Effect of the tank transfer function H(s) on the output: • Changing the amplitude of the carrier affects the steady-state output amplitude • Changing the amplitudes of the sidebands affects the ac variations of the output amplitude— i.e., the envelope • The control-to-output-envelope transfer function Genv(s) depends on the tank transfer function H(s) at the sideband frequencies fs ± fm. It doesn’t depend on H(s) at f = fm.

  29. How frequency modulation of tank input voltage introduces amplitude modulation of output envelope

  30. Poles of Genv(s) Example: H(s) has resonant poles at f = fo These poles affect the sidebands when fs ± fm = fo Hence poles are observed in Genv(s) at modulation frequencies of fm = fs – fo

  31. Outline of discussion DIRECT MODELING APPROACH • How small-signal variations in the switching frequency affect the spectrum of the switch network output voltage vs1(t) • Passing the frequency-modulated voltage vs1(t) through the tank transfer function H(s) leads to amplitude modulation of the output voltage v(t) • How to recover the envelope of the output voltage and determine the small-signal control-to-output-envelope transfer function Genv(s) PHASOR TRANSFORMATION APPROACH • Equivalent circuit modeling via the phasor transform • PSPICE simulation of Genv(s) using the phasor transform

More Related