1 / 51

General Licensing Class “G7”

General Licensing Class “G7”. Presented by the Opp Amateur Radio Club Opp, AL Friday, September 12, 2014. General Class Element 3 Course Presentation. ELEMENT 3 SUB-ELEMENTS G1 – Commission’s Rules G2 – Operating Procedures G3 – Radio Wave Propagation G4 – Amateur Radio Practices

alexis
Télécharger la présentation

General Licensing Class “G7”

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. General Licensing Class“G7” Presented by the Opp Amateur Radio Club Opp, AL Friday, September 12, 2014

  2. General Class Element 3 Course Presentation ELEMENT 3 SUB-ELEMENTS G1 – Commission’s Rules G2 – Operating Procedures G3 – Radio Wave Propagation G4 – Amateur Radio Practices G5 – Electrical Principles G6 – Circuit Components G7 – Practical Circuits G8 – Signals and Emissions G9 – Antennas G0 – Electrical and RF Safety 2

  3. G7…Practical Circuits G7A Power supplies A power-supply bleeder resistor discharges the filter capacitors providing a safety feature. Capacitors and inductors are used in a power-supply filter network. The minimum peak-inverse-voltage rating of the rectifier in a full-wave power supply should be double the normal peak output voltage of the power supply. The approximate minimum peak-inverse-voltage rating of the rectifier in a half-wave power supply should be two times the normal peak output voltage of the power supply. A desirable characteristic for capacitors used to filter the DC output of a switching power supply is low equivalent series resistance. An advantage of a switched-mode power supply as compared to a linear power supply is high frequency operation allows the use of smaller components.

  4. G7…Practical Circuits G7A Power supplies (cont) A 180 degree portion of the AC cycle is converted to DC by a half-wave rectifier. A 360 degree portion of the AC cycle is converted to DC by a full-wave rectifier. The output waveform of an unfiltered full-wave rectifier connected to a resistive load is a series of DC pulses at twice the frequency of the AC input.

  5. G7…Practical Circuits G7A Transmitters A Balanced modulator circuit is used to combine signals from the carrier oscillator and speech amplifier and send the result to the filter in a typical single sideband phone transmitter. An advantage of a crystal controlled transmitter is a Stable output frequency.

  6. G7…Practical Circuits G7A Receivers A Mixer circuit is used to process signals from the RF amplifier and local oscillator and send the result to the IF filter in a super heterodyne receiver. A Product detector circuit is used to process signals from the IF amplifier and BFO and send the result to the AF amplifier in a single-sideband phone superheterodyne receiver. The simplest combination of stages that can be combined to implement a superheterodyne receiver is an HF oscillator, mixer, and detector. A direct conversion receiver is suitable for CW and SSB reception but does not require a mixer stage or an IF amplifier. A Discriminator circuit is used in many FM receivers to convert signals coming from the IF amplifier to audio.

  7. G7…Practical Circuits G7A Filters The impedance of a low-pass filter as compared to the impedance of the transmission line into which it is inserted should be about the same. A Filter might be used to process signals from the balanced modulator and send them to the mixer in a single-sideband phone transmitter.

  8. G7…Practical Circuits G7A Fixed Resistor (3) • Schematic drawing symbols Single Cell Battery (13) NPN Transistor (4) Variable Capacitor (5) Transformer (6) Single Pole Switch (11)

  9. G7A Questions The following questions are taken directly from the Element 3 General Question Pool. These are the same questions that will appear on your test.

  10. G7A01 What safety feature does a power-supply bleeder resistor provide? • It acts as a fuse for excess voltage • It discharges the filter capacitors • It removes shock hazards from the induction coils • It eliminates ground-loop current

  11. G7A02 What components are used in a power-supply filter network? • Diodes • Transformers and transistors • Quartz crystals • Capacitors and inductors

  12. G7A03 What should be the minimum peak-inverse-voltage rating of the rectifier in a full-wave power supply? • One-quarter the normal output voltage of the power supply • Half the normal output voltage of the power supply • Double the normal peak output voltage of the power supply • Equal to the normal output voltage of the power supply

  13. G7A04 What should be the approximate minimum peak-inverse-voltage rating of the rectifier in a half-wave power supply? • One-half the normal peak output voltage of the power supply • Half the normal output voltage of the power supply • Equal to the normal output voltage of the power supply • Two times the normal peak output voltage of the power supply

  14. G7A05 What should be the impedance of a low-pass filter as compared to the impedance of the transmission line into which it is inserted? • Substantially higher • About the same • Substantially lower • Twice the transmission line impedance

  15. G7A06 Which of the following might be used to process signals from the balanced modulator and send them to the mixer in a single-sideband phone transmitter? • Carrier oscillator • Filter • IF amplifier • RF amplifier

  16. G7A07 Which circuit is used to combine signals from the carrier oscillator and speech amplifier and send the result to the filter in a typical single-sideband phone transmitter? • Mixer • Detector • IF amplifier • Balanced modulator

  17. G7A08 What circuit is used to process signals from the RF amplifier and local oscillator and send the result to the IF filter in a superheterodyne receiver? • Balanced modulator • IF amplifier • Mixer • Detector

  18. G7A09 What circuit is used to process signals from the IF amplifier and BFO and send the result to the AF amplifier in a single-sideband phone superheterodyne receiver? • RF oscillator • IF filter • Balanced modulator • Product detector

  19. G7A10 What is an advantage of a crystal controlled transmitter? • Stable output frequency • Excellent modulation clarity • Ease of switching between bands • Ease of changing frequency

  20. G7A11 What is the simplest combination of stages that can be combined to implement a superheterodyne receiver? • RF amplifier, detector, audio amplifier • RF amplifier, mixer, if amplifier • HF oscillator, mixer, detector • HF oscillator, product detector, audio amplifier

  21. G7A12 What type of receiver is suitable for CW and SSB reception but does not require a mixer stage or an IF amplifier? • A super-regenerative receiver • A TRF receiver • A super-heterodyne receiver • A direct conversion receiver

  22. G7A13 What type of circuit is used in many FM receivers to convert signals coming from the IF amplifier to audio? • Product detector • Phase inverter • Mixer • Discriminator

  23. G7A14 Which of the following is a desirable characteristic for capacitors used to filter the DC output of a switching power supply? • Low equivalent series resistance • High equivalent series resistance • Low Temperature coefficient • High Temperature coefficient

  24. G7A15 Which of the following is an advantage of a switched-mode power supply as compared to a linear power supply? • Faster switching time makes higher output voltage possible • Fewer circuit components are required • High frequency operation allows the use of smaller components • All of these choices are correct

  25. G7A16 What portion of the AC cycle is converted to DC by a half-wave rectifier? • 90 degrees • 180 degrees • 270 degrees • 360 degrees

  26. G7A17 What portion of the AC cycle is converted to DC by a full-wave rectifier? • 90 degrees • 180 degrees • 270 degrees • 360 degrees

  27. G7A18 What is the output waveform of an unfiltered full-wave rectifier connected to a resistive load? • A series of DC pulses at twice the frequency of the AC input • A series of DC pulses at the same frequency as the AC input • A sine wave at half the frequency of the AC input • A steady DC voltage

  28. G7A19 Which symbol in figure G7-1 represents a fixed resistor? • Symbol 2 • Symbol 6 • Symbol 3 • Symbol 12

  29. G7A20 Which symbol in figure G7-1 represents a single cell battery? • Symbol 5 • Symbol 12 • Symbol 8 • Symbol 13

  30. G7A21 Which symbol in figure G7-1 represents a NPN transistor? • Symbol 2 • Symbol 4 • Symbol 10 • Symbol 12

  31. G7A22 Which symbol in figure G7-1 represents a variable capacitor? • Symbol 2 • Symbol 11 • Symbol 5 • Symbol 12

  32. G7A23 Which symbol in figure G7-1 represents a transformer? • Symbol 6 • Symbol 4 • Symbol 10 • Symbol 2

  33. G7A24 Which symbol in figure G7-1 represents a single pole switch? • Symbol 2 • Symbol 3 • Symbol 11 • Symbol 12

  34. G7…Practical Circuits G7B Digital circuits (gates, flip-flops, shift registers) A “flip-flop” circuit is a digital circuit with two stable states. Digital circuits use the binary number system because binary "ones" and "zeros" are easy to represent with an "on" or "off" state. The output of a two-input NAND gate, given both inputs are “one” is Zero. The output of a NOR gate given that both inputs are “zero” is One. There are 8 states in a 3-bit binary counter. A shift register is a clocked array of circuits that passes data in steps along the array.

  35. G7…Practical Circuits G7B Amplifiers Low distortion is a characteristic of a Class A amplifier. A Class “C” power stage is appropriate for amplifying a modulated signal for the CW mode. High efficiency is an advantage of a Class C amplifier. The efficiency of an RF power amplifier is determined by dividing the RF output power by the DC input power. A linear amplifier is an amplifier whose output preserves the input waveform

  36. G7…Practical Circuits G7B Oscillators The basic components of virtually all oscillators are a filter and an amplifier operating in a feedback loop. The phase shift of the RC feedback circuit determines the frequency of an RC oscillator. The inductance and capacitance in the tank circuit determines the frequency of an LC oscillator.

  37. G7B Questions The following questions are taken directly from the Element 3 General Question Pool. These are the same questions that will appear on your test.

  38. G7B01 Which of the following describes a “flip-flop” circuit? • A transmit-receive circuit • A digital circuit with two stable states • An RF limiter • A voice-operated switch

  39. G7B02 Why do digital circuits use the binary number system? • Binary "ones" and "zeros" are easy to represent with an "on" or "off" state • The binary number system is most accurate • Binary numbers are more compatible with analog circuitry • All of these answers are correct

  40. G7B03 What is the output of a two-input NAND gate, given both inputs are “one”? • Two • One • Zero • Minus One

  41. G7B04 What is the output of a NOR gate given that both inputs are “zero”? • Zero • One • Minus one • The opposite from the previous state

  42. G7B05 How many states are there in a 3-bit binary counter? • 3 • 6 • 8 • 16

  43. G7B06 What is a shift register? • A clocked array of circuits that passes data in steps along the array • An array of operational amplifiers used for tri-state arithmetic operations • A digital mixer • An analog mixer

  44. G7B07 What are the basic components of virtually all oscillators? • An amplifier and a divider • A frequency multiplier and a mixer • A circulator and a filter operating in a feed-forward loop • A filter and an amplifier operating in a feedback loop

  45. G7B08 What determines the frequency of an RC oscillator? • The ratio of the capacitors in the feedback loop • The value of the inductor in the tank circuit • The phase shift of the RC feedback circuit • The gain of the amplifier

  46. G7B09 What determines the frequency of an LC oscillator? • The number of stages in the counter • The number of stages in the divider • The inductance and capacitance in the tank circuit • The time delay of the lag circuit

  47. G7B10 Which of the following is a characteristic of a Class A amplifier? • Low standby power • High Efficiency • No need for bias • Low distortion

  48. G7B11 For which of the following modes is a Class C power stage appropriate for amplifying a modulated signal? • SSB • CW • AM • All of these answers are correct

  49. G7B12 Which of the following is an advantage of a Class C amplifier? • High efficiency • Linear operation • No need for tuned circuits • All of these answers are correct

  50. G7B13 How is the efficiency of an RF power amplifier determined? • Divide the DC input power by the DC output power • Divide the RF output power by the DC input power • Multiply the RF input power by the reciprocal of the RF output power • Add the RF input power to the DC output power

More Related