1 / 10

Fast Tuned Active High-Q MMIC Filters for AESA Radar Applications

Fast Tuned Active High-Q MMIC Filters for AESA Radar Applications. Why Do It?. Fast Tuned Notch Filter (FTNF) Concept originally developed for Electronic Surveillance (ES) systems, to counter on-board Frequency Agile, High Duty Cycle emitters

emilyolivera
Télécharger la présentation

Fast Tuned Active High-Q MMIC Filters for AESA Radar Applications

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Fast Tuned Active High-Q MMIC Filters for AESA Radar Applications

  2. Why Do It? • Fast Tuned Notch Filter (FTNF) Concept originally developed for Electronic Surveillance (ES) systems, to counter on-board Frequency Agile, High Duty Cycle emitters • However, Radars also experience a wide variety of in-band interferers: • Naval – Consort ship emitters, intentional Interferers, unintentional interferers • Air – Wing-man emitters, intentional Interferers, unintentional interferers • Other Functions (eg ES) are desirable: • Requires mitigation of own Tx break-through • All the above applications require highly agile filtering, and extremely low SWaP to embed in Radar Transmit Receive Modules (TRMs)

  3. X-Band MMIC FTNF Advantages • Enables dynamic management of AESA Radar in-band interferers • Extremely Compact Design • Chip dimensions 2.5mm x 2.5mm • Suitable to integrate into Radar TRMs • Low RF & support component count • Minimal board footprint • High MTBF • Simple control scheme • Only two analogue inputs required to control the notch frequency and depth. • One enable / disable line Freq Control Notch On/Off MMIC Notch Filter RF I/P RF O/P Gain Control Bias -V Bias +V

  4. X-Band MMIC FTNF Initial Test Jig Test Results • High Q Stable notch response • 2GHz tuning range (previous hybrid design was 1GHz) • Notch depths >-30dB (can be dynamically varied) • Low insertion loss • VDD = 4V, IDD = 40mA, 160mW • Note: gap in middle due to design error – now resolved

  5. IMD3 Measurements – 9.38GHz • Third order product measured with one i/p signal in the notch and one out of the notch • I/P powers -10dBm and 0dBm single tones 0dBm Input Power -10 dBm Input Power

  6. MMIC FTNF With bandpass tap • The FTNF can include a port to monitor the attenuated interference signal • Enables truly dynamic interferer management • Optimises spectrum visibility

  7. Control Aspects – Fast Tuning • Fast Tune Speed typ 250ns • Requires: • High Speed DAC and Switch Ctrl • High Speed Memory Function • Programmable Logic (FPGA) / NVRAM • High Speed Interface • Parallel – Practicalities of routing across TR array • High Speed Serial – Power Dissipation • Size and Power Penalty • Control can be shared across sub-arrays

  8. Control Aspects (Continued) • Slow Tune Speed typ 30us • Use single system on chip (microcontroller with peripherals, inc DAC and Op-Amps) • e.g. MAXQ8913, PIC16F1778 • Low Power • Typically 5x5mm Package • Possibly in Bare Die • Serial SPI Interface @1Mbps • 10 bit Freq in 10us, DAC settle in 20us = 30us

  9. Outline Specification All-pass frequency range 6-18GHz Notch Tuning Range 8.5 – 9.5GHz V1 8.5 – 10.5GHz V2 Notch width (-15dB) 30MHz typ Notch width (-5dB) 150MHz typ Allpass insertion loss <1dB (full band) <0.4dB typ 8-10GHz Return loss outside notch 20dB typ allpass 20dB typ Input IP3 -10dBm i/p pwr 22dBm typ (one signal in notch) 0dBm i/p pwr 12dBm typ Max input power +20dBm abs max Tuned ‘tap’ output tbd Notch control allpass/notch 0V / -5V Frequency control -4V to -20V Notch depth control 0V to +2.5V (5mA) Supply voltage +4V / 40mA -3V max (gate bias)

  10. MIC/MMIC Hybrid S-band FTNF • The passive circuits used in the X-band FTNF MMIC become too large to be feasible for full MMIC implementation. • Solution is Hybrid MIC/MMIC layout where the Passive parts are implemented on alumina MIC substrate and the active parts, the amplifiers ans attenuator are implemented on MMIC. • The Hybrid design can be implemented in a 12 x 6 mm MIC tile.

More Related