1 / 34

Project 16 Digital Whammy Bar

Project 16 Digital Whammy Bar. Tim Kamman | Jason Freeck | Parker Brown. 4/7/2014. Agenda. Introduction and Objectives PCB Design Evaluation Board Implementation Software design Sensors Requirements and Verification Conclusion. Introduction. Aftermarket tremolo bar Expensive

lida
Télécharger la présentation

Project 16 Digital Whammy Bar

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Project 16Digital Whammy Bar Tim Kamman| Jason Freeck | Parker Brown 4/7/2014

  2. Agenda • Introduction and Objectives • PCB Design • Evaluation Board Implementation • Software design • Sensors • Requirements and Verification • Conclusion

  3. Introduction • Aftermarket tremolo bar • Expensive • Permanent • Difficult to tune • Limited shift possible • Solution: electronic implementation • Compact • Removable • Inexpensive

  4. Objectives • High quality tremolo bar effect using DSP • Available at lower cost than existing options • Non-intrusive and temporary installation • Limited user setup required

  5. Block Diagram

  6. PCB Design • Started with a single board design • ECE shop limitations → two board design • Power Board • Processing Board

  7. Voltage Regulator

  8. LM317 Voltage Regulator

  9. Power Simulations • Simulated voltage regulator to determine power consumption • 92.08 mW

  10. Power Budget • Typical 9 V Battery: 5.1 Wh

  11. DSP Chip • Analog Devices ADAU1701: • Audio Processor • ADC/DAC built in • Sampling rates up to 192KHz supported • GPIOs

  12. USB to I2C Interface

  13. Output Filter

  14. Verifying Output Filter

  15. Output Filter Tolerance Analysis • Ensure cutoff frequencies stay above the desired sampling frequency • Maximum 5% change in component values

  16. PCB Design: Cost Total: $93.72

  17. PCB Design: Difficulties • Complex design • Bulky • Two boards • Limited by board layers/planes • Difficulty soldering • Burnt board

  18. Evaluation Board Implementation Cost of Evaluation Board: $219.38

  19. Software Flowchart

  20. SigmaStudio • Proprietary software for Analog Devices DSP chips • Uses graphical blocks to program effects • Frequency shift included

  21. Code Walkthrough Scale down input signal from sensor Set sensitivity mode

  22. IR Sensor • Soldered IR sensor to 5 V power input • Bypassed current limiting diode

  23. IR Sensor: Issues • “Cut-In” at middle of shift range • Accidental triggering during play • Digital artifacts from IR sampling

  24. Potentiometer Sensor • Output Range: 0 to 3.3 V • Powered using external battery • Physical sensor • Better emulation of the feel of tremolo bar • More granular control • Purely analog, no sampling effects

  25. Requirements and Verification

  26. Requirements and Verification Original Shifted -30 dB

  27. Requirements and Verification

  28. Requirements and Verification Low Setting: Shifted to 387 Hz High Setting: Shifted to 287 Hz

  29. Requirements & Verification

  30. Future Work • Provisional patent application • Mounting system • PCB board implementation • Lower cost • Power potentiometer off of the board • Physical tremolo bar

  31. Conclusion • No digital tremolo bar available • Only alternative: aftermarket installation • Permanent • Invasive • Expensive • Digital tremolo bar can solve these problems • Low-Cost • Less Intrusive • Removable

  32. Questions?

  33. Appendix: PCB Board Layout

  34. Appendix: Phase Vocoder

More Related