1 / 19

ADC and DAC

ADC and DAC. Reason for Signal Conversion. AD2 DA1. digital. Topics. Analog to Digital Conversion Digital to Analog Conversion. Analog to Digital Conversion. Digilent’s PMODAD2. Schematic of PMOD AD2. PMODAD2 uses AD7991 from Analog Devices. Successive Approximation ADC.

jonas-richards
Télécharger la présentation

ADC and DAC

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. ADC and DAC

  2. Reason for Signal Conversion AD2 DA1 digital

  3. Topics • Analog to Digital Conversion • Digital to Analog Conversion

  4. Analog to Digital Conversion

  5. Digilent’s PMODAD2

  6. Schematic of PMOD AD2 PMODAD2 uses AD7991 from Analog Devices

  7. Successive Approximation ADC The analog input voltage (VIN) is held on a track/hold. The N-bit register is first set to midscale (that is, 100... .00, where the MSB is set to 1). This forces the DAC output (VDAC) to be VREF/2. A comparison is then performed to determine if VIN is less than, or greater than, VDAC. If VIN is greater than VDAC, the comparator output is a logic high, or 1, and the MSB of the N-bit register remains at 1. Conversely, if VIN is less than VDAC, the comparator output is a logic low.

  8. Successive Approximation ADC 3. The SAR control logic then moves to the next bit down, forces that bit high, and does another comparison. The sequence continues all the way down to the LSB. 4. Once this is done, the conversion is complete and the N-bit digital word is available in the register.

  9. Graphical Illustration The y-axis (and the bold line in the figure) represents the DAC output voltage. In the example, the first comparison shows that VIN < VDAC. Thus, bit 3 is set to 0. The DAC is then set to 01002 and the second comparison is performed. As VIN > VDAC, bit 2 remains at 1. The DAC is then set to 01102, and the third comparison is performed. Bit 1 is set to 0, and the DAC is then set to 01012 for the final comparison. Finally, bit 0 remains at 1 because VIN > VDAC.

  10. Analog to Digital Conversion Using a Capacitive DAC

  11. During Acquisition Stage

  12. Signal Conversion (1) (-Vin)

  13. Signal Conversion (2) (-Vin+VREF/2) The comparator output yields a logic 1 if VCOMMON < 0 (i.e., VIN > ½ × VREF). The comparator output yields logic 0 if VIN < ½ × VREF. If the comparator output is logic 1, then the bottom plate of the MSB capacitor stays connected to VREF. Otherwise, the bottom plate of the MSB capacitor is connected back to ground.

  14. Signal Conversion (3) (-Vin+VREF/2) This slide assumes that MSB is a 1. In general, VCOMMON = -VIN + BN-1 × VREF/2 + BN-2 × VREF/4 + BN-1 × VREF/8 + ... + B0 × VREF/2N-1

  15. Digielent’s DA1

  16. Current Steering DAC

  17. Current Steering DAC (2)

  18. Current Steering DAC (3)

  19. R2R 3-Bit Digital to Analog Converter 741 Op-Amp Chapter 5

More Related